Most people love jewels designed in a particular manner and with various materials, but they never question how they are made. It is important to note that multiple processes are involved before the final product is gotten. The methods consist of the process of mixing the right materials and colors to come with specific designs. This discussion will focus on the procedures of making Tufa casting custom jewelry NM.
Pieces of stone where the design will be made are prepared before other process kicks off. The size of the stones to be used is determined by the choice and type of models the designer ought to create. After the right size have been cut, the next thing is to smoothen all of them and make them flat. The aim of flattening them is to make them identical and perfect to each other.
After the stones have been prepared, it is time to make sketches of what one wants to produce. Sketching takes a lot of time because if errors are made, correcting them again can be costly and time consuming. Therefore, when the sketching process begins one needs to stay in a conducive environment completely.
After the sketched have been drawn carving of the stone should happen. Carving should be carried out using tools that are recommended for the process. Here useful tools include chisels, wood filed and sewing needles because they make the process much more manageable. There is a need to have this process correctly done because when mistakes are made there will be little room to correct them and there should be no air rooms left. Carving leaves space where silver fillings will be poured to get the desired model.
Before silver is poured in the intended space, stones have to be carbonized to get rid of oxygen. The pieces of stones are attached using clamps and rubbers, and this makes the process as perfect as possible. Solid silver is then put in a crucible, and high temperatures of heat are introduced to melt it into an exceptional liquid form. When silver is in its liquid form state, it is then poured on spaces that were left.
Sand is used to smoothening and clean the model. Sand cleans and removes the unwanted parts, and the good news is that the texture is not affected at all. Also, citric acid pickling solution is used in cleaning the surfaces. The pickling solution is effective in removing any traces of fire that are gotten when the soldering process is taking process.
At this point polishing is inevitable. The sole aim of polishing to have the products look attractive and appealing. The most common ways to shine the designs involved the use of water, rubber and other recommended polishing compounds. The different stages of polishing will use compounds that are either abrasive or non abrasive.
On completion of most processes, the products are almost ready for the market. Although they are available, there is room for designers to put various styles on them before they are sold. This can be done keeping mind your target market and what you intended to create. As much as other stages take a lot of time, sanding and polishing take the most time.
Pieces of stone where the design will be made are prepared before other process kicks off. The size of the stones to be used is determined by the choice and type of models the designer ought to create. After the right size have been cut, the next thing is to smoothen all of them and make them flat. The aim of flattening them is to make them identical and perfect to each other.
After the stones have been prepared, it is time to make sketches of what one wants to produce. Sketching takes a lot of time because if errors are made, correcting them again can be costly and time consuming. Therefore, when the sketching process begins one needs to stay in a conducive environment completely.
After the sketched have been drawn carving of the stone should happen. Carving should be carried out using tools that are recommended for the process. Here useful tools include chisels, wood filed and sewing needles because they make the process much more manageable. There is a need to have this process correctly done because when mistakes are made there will be little room to correct them and there should be no air rooms left. Carving leaves space where silver fillings will be poured to get the desired model.
Before silver is poured in the intended space, stones have to be carbonized to get rid of oxygen. The pieces of stones are attached using clamps and rubbers, and this makes the process as perfect as possible. Solid silver is then put in a crucible, and high temperatures of heat are introduced to melt it into an exceptional liquid form. When silver is in its liquid form state, it is then poured on spaces that were left.
Sand is used to smoothening and clean the model. Sand cleans and removes the unwanted parts, and the good news is that the texture is not affected at all. Also, citric acid pickling solution is used in cleaning the surfaces. The pickling solution is effective in removing any traces of fire that are gotten when the soldering process is taking process.
At this point polishing is inevitable. The sole aim of polishing to have the products look attractive and appealing. The most common ways to shine the designs involved the use of water, rubber and other recommended polishing compounds. The different stages of polishing will use compounds that are either abrasive or non abrasive.
On completion of most processes, the products are almost ready for the market. Although they are available, there is room for designers to put various styles on them before they are sold. This can be done keeping mind your target market and what you intended to create. As much as other stages take a lot of time, sanding and polishing take the most time.
About the Author:
Get a summary of the things to keep in mind when choosing a tufa casting custom jewelry NM designer and more information about an experienced designer at http://www.bojoejewelry.com now.